Kia Cadenza: Windshield Wiper/Washer / Front Wiper Motor Repair procedures

Kia Cadenza YG 2016-2025 Service Manual / Body Electrical System / Windshield Wiper/Washer / Front Wiper Motor Repair procedures

Removal

1.	Loosen the windshield wiper arm nut (B) after removing a wiper cap (A).

2.	Remove the windshield wiper arm and blade (A).

3.	If necessary, release the wiper blade fixing clip by pulling up and remove the wiper blade from the inside radius of wiper arm.

4.	Disconnect the washer hose (A) connected to cowl top cover.

5.	Remove the weather strip and the cowl top cover (A) after removing rivets.

6.	Disconnect the wiper motor connector (A) from the wiper motor & linkage assembly.

7.	Remove the windshield wiper motor and linkage assembly (A) after removing 2 bolts.

Hold the wiper motor crank arm and remove the upper linkage (A) from the wiper motor crank arm.

Before remving the wiper motor and linkage assembly, make sure that the linkage is stopped at auto stop position.

To install the wiper motor crank arm exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.

Be careful not to bend the linkage.

Remove the lower linkage (A) from the wiper motor crank arm.

To install the wiper motor crank arm (A) exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.

Be careful not to bend the linkage.

10.	Remove the crank arm (A) after loosening a nut.

11.	Remove the wiper motor (A) after loosening the bolts.

Installation

1.	Install the wiper motor.

Install the crank arm.

Tightening torque :

12.7 ~ 17.6N.m (1.3 ~ 1.8, kgf.m, 9.4 ~ 13.0 lb-ft)

To install the wiper motor crank arm, make sure that the linkage (B) is aligned with the crank arm (A) in straight line and set the angle of each linkages exactly.

3.	Install the lower and upper linkage to the wiper motor crank arm.

Install the wiper motor and linkage assembly and then connect the wiper motor connector.

Tightening torque :

7 ~ 11N.m (0.7 ~ 1.1, kgf.m, 5.0 ~ 7.9 lb-ft)

5.	Install the cowl top cover.

Install the windshield wiper arm and blade.

Tightening torque :

28 ~ 32 N.m (2.8 ~ 2.7 kgf.m, 20.2 ~ 23.1 lb-ft)

–	The windshield wiper motor must be cycled to make sure that it is in the auto stop position. If necessary, adjust the wiper arm and blade.

7.	Install the wiper arm and blade to the specified position. A : Auto stop position (Blade)

Set the cowl top cover on the specified spray position.

–	When you turn on the washer, confirm 50% or more of washer fluid lands within the spray area.

–	If the spray area is not within the standard positions, adjust the nozzle(s).

Specified position	Distance (in)	Distance (mm)
A	33.1	842
B	4.7	120
C	20.9	531
D	27.9	710
E	18.2	463
F	21	534
G	12	306

Inspection

Speed Operation Check

Remove the connector (A) from the wiper motor.

No.	Description	No.	Description
1	-	4	High
2	Battery (+)	5	GND
3	Gear P	6	Low

2.	Attach the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 5.

Check that the motor operates at low or high speed as below table.

Common sources of contamination are insects, tree sap, and hot wax treatments used by some commercial car washes. If the blades are not wiping properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.

Front Wiper Motor Components and Components Location

Component Location 1. Cap2. Nut3. Wiper arm & blade4. Rivet5. Cowl top cover6. Bolt7. Wiper motor & linkage assembly ...

Front Washer Motor Repair procedures

Inspection 1. With the washer motor connected to the reservoir tank, fill the reservoir tank with water. Before filling the reservoir tank with water, check the fil ...

Other information:

Kia Cadenza YG 2016-2025 Service Manual: Seat Heater Repair procedures

Inspection First Seat Heater 1. Check for continuity and measure the resistance between No.1 and NO.4 terminals. No.DescriptionNo.Description1Heater (-)3NTC (+)2NTC (-)4Heater (+) Standard value (Fabric / Leather) Cushion : 1.04 Ω ± 10% Back : 1.1 Ω ± 10% Set : 2.14 Ω ± 10% ...

Kia Cadenza YG 2016-2025 Service Manual: Head Lamps Repair procedures

Inspection 1. Check-points upon head lamp failure (HID) (1) Check the battery voltage. (Low beam will be on when the battery voltage above 9V.) (2) Check the fuse and relay. (3) Check the polarity of ballast. (If the polarity are changed, low beam doesn''t lighten) (4) Check the bu ...