Kia Cadenza YG: Electric Power Steering / Steering Column and Shaft Repair procedures

Kia Cadenza YG 2016-2021 Service Manual / Steering System / Electric Power Steering / Steering Column and Shaft Repair procedures

Replacement
1.
Disconnect the battery negative cable from the battery and then wait for at least 30 seconds.
2.
Turn the steering wheel so that the front wheels can face straight ahead.
3.
Push the pin (A) and then disconnect the airbag module from the steering wheel.

4.
Disconnect the airbag module connector (A) & horn connector (B) and then remove the airbag module from the steering wheel.

5.
Disconnect the lock nut (A) & connector (B) and then remove the steering wheel by using special service tools. (09561-11001)
Tightening torque :
39.2 ~ 44.1N.m (4.0 ~ 4.5kgf.m, 28.9 ~ 32.5lb-ft)

   
Do not hammer on the steering wheel to remove it; it may damage the steering column.
6.
Loosen the screw and then remove the steering column upper (A) and lower shroud (B).

7.
Disconnect the connector (A) and then remove the clock spring (B).

   
•
When assembling set the center position by setting the marks between the clock spring and the cover into line. Make an array the mark (▶◀) by turning the clock spring clockwise to the stop and then 2.0 revolutions counterclockwise.
8.
Disconnect the connector (A).

9.
Loosen the screw and then remove the multifunction switches (A).

10.
Remove the crash pad side cover, Fuse box cover and lower crash pad.
(Refer to Body - "Crash Pad Lower Panel")
11.
Loosen the screw and then remove the shower tilt (A).

12.
Loosen the bolt (A) and then disconnect the universal joint assembly from the pinion of th
Tightening torque :
32.4 ~ 37.3N.m (3.3 ~ 3.8kgf.m, 23.9 ~ 27.5lb-ft)

   
•
Lock the steering wheel in the straight ahead position to prevent the damage of the clock spring inner cable when you handle the steering wheel.
•
Do not use the bolt again.
13.
Disconnect all connectors connected the steering column & EPS unit assembly.
14.
Remove the steering column & EPS unit assembly by loosening the mounting bolt (A) and nuts (B).
Tightening torque :
Nut : 12.7 ~ 17.7N.m (1.3 ~ 1.8kgf.m, 9.4 ~ 13.0lb-ft)
Bolt : 44.1 ~ 49.0N.m (4.5 ~ 5.0kgf.m, 32.5 ~ 36.2lb-ft)

   
If MDPS type, you must be EPS type recognition
(Refer to Electric Power Steering - Repair procedures)
15.
Installation is the reverse of the removal.
Universal joint assembly
1.
Loosen the bolt (A) and then disconnect the universal joint assembly from the steering column assembly.
Tightening torque :
49.0 ~ 58.8N.m (5.0 ~ 6.0kgf.m, 43.3 ~ 21.7lb-ft)

2.
Reassembly is the reverse of the disassembly.
   
•
Do not disassemble the EPS module from the column shaft.
Inspection
1.
Check the steering column for damage and deformation.
2.
Check the steering column for damage and deformation.
3.
Check the join bearing for damage and wear.
4.
Check the tilt bracket for damage and cracks.
5.
Check the key lock assembly for proper operation and replace it if necessary.

    General Inspection After or before servicing the EPS system, perform the troubleshooting and test procedure as follows. Compare the system condition with normal condition in the table below and if abnormal symptom is detected, perform necessary remedy and inspection.

    Components 1. Tie-rod end2. Lock nut3. Bellows4. Bellows clip5. Tie rod6. Rack bar7. Dust packing8. Dust cap9. Oil seal10. Pinion plug11. Pinion assembly12.

    Other information:

    Kia Cadenza YG 2016-2021 Service Manual: Components and Components Location

    C

    Kia Cadenza YG 2016-2021 Service Manual: Condenser Repair procedures

    Inspection 1. Check the condenser fins for clogging and damage. If clogged, clean them with water, and blow them with compressed air. If bent, gently bend them using a screwdriver or pliers. 2. Check the condenser connections for leakage, and repair or replace it, if required.

    Categories

     
    Copyright © 2025 www.kcadenzavg.com - 0.0224