Kia Cadenza YG: Cylinder Head Assembly / Valve Clearance Adjustment

Kia Cadenza YG 2016-2021 Service Manual / Engine Mechanical System / Cylinder Head Assembly / Valve Clearance Adjustment

Valve Clearance Inspection And Adjustment
   
Inspect and adjust the valve clearance when the engine is cold (Engine coolant temperature : 20°C(68°F)) and cylinder head is installed on the cylinder block.
1.
Remove the cylinder head cover.
(Refer to Cylinder Head Assembly - "Cylinder Head Cover")
2.
Set No.1 cylinder to TDC/compression.
(1)
Turn the crankshaft pulley clockwise and align its groove with the timing mark "T" of the lower timing chain cover.

(2)
Check that the mark of the camshaft timing sprockets are in straight line on the cylinder head surface as shown in the illustration.
If not, turn the crankshaft clockwise one revolution (360°).

   
Do not rotate engine counterclockwise.
3.
Inspect the valve clearance.
(1)
With No.1 cylinder at TDC inspect clearances only on the valves shown in diagram below.

Measurement method.
a.
Using a thickness gauge, measure the clearance between the tappet and the base circle of camshaft.
b.
Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement adjusting tappet.
Valve clearance (Engine coolant temperature : 20°C [68°F])
[Specification]
Intake : 0.17 ~ 0.23mm (0.0067 ~ 0.0090in.)
Exhaust : 0.27 ~ 0.33mm (0.0106 ~ 0.0129in.)
(2)
Turn the crankshaft pulley clockwise one revolution (360°) and align the groove with timing mark "T" of the lower timing chain cover.
(3)
With No.4 cylinder at TDC inspect clearances only the valves shown in diagram below. (Refer to procedure step 1.)

4.
Adjust the intake and exhaust valve clearance.
(1)
Set the No.1 cylinder to the TDC/compression.
(2)
Remove the timing chain.
   
Before removing the timing chain, mark the RH/LH timing chain with an identification based on the location of the sprocket because the identification mark on the chain for TDC (Top Dead Center) can be erased.

(3)
Remove the fuel pump bracket (A).

(4)
Remove the LH/RH camshaft bearing cap (A) and thrust bearing cap (B).

(5)
Remove the LH/RH camshaft assembly (A).

(6)
Remove the tappets.
(7)
Measure the thickness of the removed tappet using a micrometer.

(8)
Calculate the thickness of a new tappet so that the valve clearance comes within the specified value.
T : Thickness of removed tappet
A : Measured valve clearance
N : Thickness of new tappet
Intake : N = T + [A - 0.20mm(0.0079in.)]
Exhaust : N = T + [A - 0.30mm (0.0118in.)]
(9)
Select a new tappet with a thickness as close as possible to the calculated value.
   
Shims are available in 41size increments of 0.015mm (0.0006in.) from 3.00mm (0.118in.) to 3.600mm (0.1417in.)
(10)
Place a new tappet on the cylinder head.
   
Apply engine oil at the selected tappet on the side and top surface.
(11)
Install the intake and exhaust camshaft.
(12)
Install the bearing caps.
(Refer to Cylinder Head Assembly - "CVVT & Camshaft")
(13)
Install the timing chain.
(Refer to Timing System - "Timing Chain")
(14)
Turn the crankshaft two turns in the operating direction (clockwise) and realign crankshaft sprocket and camshaft sprocket timing marks.

(15)
Recheck the valve clearance.
Valve clearance (Engine coolant temperature : 20°C [68°F])
[Specification]
Intake : 0.17 ~ 0.23mm (0.0067 ~ 0.0090in.)
Exhaust : 0.27 ~ 0.33mm (0.0106 ~ 0.0129in.)

    Components 1. RH Cylinder head2. RH Cylinder head gasket3. LH Cylinder head4. LH Cylinder head gasket5. Cylinder block 1. Camshaft bearing cap 2.

    Removal [LH] 1. Remove the Intake manifold. (Refer to Intake And Exhaust System - "Intake Manifold") 2. Remove the high pressure fuel pump.

    Other information:

    Kia Cadenza YG 2016-2021 Service Manual: Repair procedures

    Refrigerant System Service Basics Refrigerant Recovery Use only service equipment that is U.L-listed and is certified to meet the requirements of SAE J2210 to remove HFC-134a(R-134a) from the air conditioning system.     – Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or th

    Kia Cadenza YG 2016-2021 Service Manual: Blower Resistor Repair procedures

    Inspection 1. Measure terminal - to - terminal resistance of blower resistor. 2. If measure resistance isnot within specification, the blower resistor must be replaced. Replacement 1. Disconnect the negative (-) battery terminal. 2. Remove the crash pad lower cover (A) and then disconnect the connector (B).

    Categories

     
    Copyright © 2026 www.kcadenzavg.com - 0.0236