Kia Cadenza: Cooling System / Water Temperature Control Assembly Repair procedures

Kia Cadenza YG 2016-2025 Service Manual / Engine Mechanical System / Cooling System / Water Temperature Control Assembly Repair procedures

Removal and Installation
   
To avoid damage, unplug the wiring connectors carefully while holding the connector portion.
   
Mark all wiring and hoses to avoid misconnection.
Water Temperature Control Assembly
1.
Disconnect the battery negative terminal.
2.
Remove the engine room under cover.
(Refer to Engine And Transaxle Assembly - "Engine Room Under Cover")
3.
Loosen the drain plug and drain the engine coolant.
(Refer to Cooling System - "Coolant")
4.
Remove the air cleaner assembly.
(Refer to Intake and Exhaust System - "Air cleaner")
5.
Disconnect the radiator upper hose (A) and lower hose (B).

   
When installing radiator hoses, install as shown in illustrations.

6.
Disconnect the WTS & gauge unit connector (A).

7.
Separate the engine wiring protector mounted on the water temperature control assembly.

   
When installing, be sure to install the wiring protector mounting bolts of the original.
If other bolts(longer or larger) has been installed, this can damage the water temperature control assembly and coolant may be leak.
8.
Disconnect the throttle body coolant hoses (A).

9.
Disconnect the heater hoses (A).

10.
Remove the water temperature control assembly (A).

Tightening torque :
19.6 ~ 23.5 N.m (2.0 ~ 2.4 kgf.m, 14.5 ~ 17.4 lb-ft)

11.
Install in the reverse order of removal.
12.
Fill the radiator with coolant and check for leaks.
(Refer to Cooling System - "Coolant")
   
Refill engine coolant.
Refill radiator and reservoir tank with engine coolant.
Bleed air from the cooling system.
Start engine and let it run until it warms up. (Until the radiator fan operates 3 or 4 times.)
Turn Off the engine. Check the level in the radiator, add coolant if needed. This will allow trapped air to be removed from the cooling system.
Put radiator cap on tightly, then run the engine again and check for leaks.
Clean the battery posts and cable terminals with sandpaper assemble them, then apply grease to prevent corrosion.
Water Center Pipe
1.
Remove the intake manifold.
(Refer to Intake And Exhaust System - "Intake Manifold")
2.
Remove the water temperature control assembly.
(Refer to Cooling System - "Water Temperature Control Assembly")
3.
Remove the water center pipe (A).

Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

   
Do not reuse water pipe O-ring.
4.
Install in the reverse order of removal.
Water Temperature Control Assembly Components and Components Location
Components 1. Water pipe 2. Throttle body coolant hose & pipe3. Water temperature control assembly4. O-ring ...

Water pump Components and Components Location
Components 1. Water pump pulley2. Water pump 3. Water pump gasket ...

Other information:

Kia Cadenza YG 2016-2025 Owners Manual: Removing and storing the spare tire


Turn the tire hold-down wing bolt counterclockwise. Store the tire in the reverse order of removal. To prevent the spare tire and tools from “rattling” while the vehicle is in motion, store them properly. If it is hard to loosen the tire holddown wing bolt by hand, you can loo ...

Kia Cadenza YG 2016-2025 Owners Manual: To decrease Smart Cruise Control set speed


Follow either of these procedures: Move the SET- switch down and hold it. Your vehicle set speed will decrease by 5 mph (10 km/h). Release the switch at the speed you want. Move the SET- switch down and release it immediately. The cruising speed will decrease by 1.0 mph ...

Copyright © www.kcadenzavg.com 2017-2025