Kia Cadenza YG: Engine And Transmission Assembly / Engine Mounting Repair procedures

Kia Cadenza YG 2016-2021 Service Manual / Engine Mechanical System / Engine And Transmission Assembly / Engine Mounting Repair procedures

Removal and Installation
Engine Mounting Bracket
1.
Disconnect the battery negative terminal.
2.
Remove the engine room under cover.
(Refer to Engine And Transaxle Assembly – “Engine Room Under Cover”)
3.
Install the jack to the edge of the upper oil pan to support the engine.

   
Insert the rubber block between jack and upper oil pan.
4.
Remove the engine mounting support bracket (A).
Tightening torque :
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)
5.
Remove the engine mounting bracket (B).
Tightening torque :
58.8 ~ 73.5 N.m (6.0 ~ 7.5 kgf.m, 43.4 ~ 54.2 lb-ft)

6.
Install in the reverse order of removal.
Roll rod Bracket
1.
Remove the engine room under cover.
(Refer to Engine And Transaxle Assembly - “Engine Room Under Cover”)
2.
Remove the roll rod bracket (A).
Tightening torque
Bolt (B) :
107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.0 lb-ft)
Bolts (C) :
49.0 ~ 63.7 N.m ( 5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)

3.
Install in the reverse order of removal.
Transaxle Mounting Bracket
1.
Remove the air cleaner assembly.
(Refer to Intake and Exhaust System - "Air Cleaner")
2.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
3.
Remove the engine control module (ECM).
(Refer to Engine Control/Fuel System - “Engine Control Module (ECM)”)
4.
Remove the engine room under cover.
(Refer to Engine And Transaxle Assembly - “Engine Room Under Cover”)
5.
Install the jack to the edge of transaxle.
6.
Remove the transaxle mounting bracket.
(1)
Remove the service cover (A).

(2)
Remove the transaxle mounting bolts (A).
Tightening torque:
107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.0 lb-ft)
(3)
Remove the transaxle mounting bracket (B).
Tightening torque:
49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)

7.
Install in the reverse order of removal.

    Components 1. Transaxle mounting bracket2. Roll rod bracket3. Sub frame4. Engine mounting bracket5. Engine mounting support bracket

    Removal     • Use fender covers to avoid damaging painted surfaces. • To avoid damage, unplug the wiring connectors carefully while holding the connector portion.

    Other information:

    Kia Cadenza YG 2016-2021 Service Manual: Height Sensor Repair procedures

    Removal Height Sensor 1. Disconnect the negative (-) battery terminal. 2. Remove the height sensor linkage (A) installed on the front axle and rear axle. [Front] [Rear] Installation Height Sensor 1. Install the height sensor assembly after connecting the connector.

    Kia Cadenza YG 2016-2021 Service Manual: Condenser Repair procedures

    Inspection 1. Check the condenser fins for clogging and damage. If clogged, clean them with water, and blow them with compressed air. If bent, gently bend them using a screwdriver or pliers. 2. Check the condenser connections for leakage, and repair or replace it, if required.

    Categories

     
    Copyright © 2026 www.kcadenzavg.com - 0.0337