Kia Cadenza YG: Driveshaft and axle / Specifications

Kia Cadenza YG 2016-2021 Service Manual / Driveshaft and axle / Specifications

Specification
Engine & T/M
Joint type
Max. permissible angle
Inner
Outer
Inner
Outer
Lambda 3.3 GDI
VTJ#25
BJ#26
21°
46.5°

Tightening Torques
Item
N.m
kgf.m
Ib-ft
Front
Wheel nut
88.2 ~ 107.8
9.0 ~ 11.0
65.0 ~ 79.5
Drive shaft coking nut
274.6 ~ 294.2
28.0 ~ 30.0
202.5 ~ 217.0
Strut assembly lower mounting bolt
196.1 ~ 215.7
20.0 ~ 22.0
144.7 ~ 159.1
Brake caliper mounting bolt
78.4 ~ 98.0
8.0 ~ 10.0
57.8 ~ 72.3
Wheel speed sensor mounting bolt
6.8 ~ 9.8
0.7 ~ 1.0
5.0 ~ 7.2
Brake disc mounting bolt
4.9 ~ 5.8
0.5 ~ 0.6
3.6 ~ 4.3
Lower ball joint mounting bolt
98.0 ~ 117.6
10.0 ~ 12.0
72.3 ~ 86.7
Tie rod end ball joint nut
34.3 ~ 44.0
3.5 ~ 4.5
25.3 ~ 32.5
Rear
Wheel nut
88.2 ~ 107.8
9.0 ~ 11.0
65.0 ~ 79.5
Shock absorber upper mounting bolt
49.0 ~ 63.7
5.0 ~ 6.5
36.2 ~ 47.0
Shock absorber lower mounting nut
137.2 ~ 156.9
14.0 ~ 16.0
101.2 ~ 115.7
Brake caliper mounting bolt
78.4 ~ 98.0
8.0 ~ 10.0
57.8 ~ 72.3
Wheel speed sensor mounting bolt
6.8 ~ 10.7
0.7 ~ 1.1
5.0 ~ 7.9
Brake disc mounting bolt
4.9 ~ 5.8
0.5 ~ 0.6
3.6 ~ 4.3
Hub assembly mounting bolt
78.4 ~ 88.2
8.0 ~ 9.0
57.8 ~ 65.0
Upper arm ball joint mounting nut
137.2 ~ 156.9
14.0 ~ 16.0
101.2 ~ 115.7
Lower arm mounting bolt
137.2 ~ 156.9
14.0 ~ 16.0
101.2 ~ 115.7
Assist arm ball joint mounting nut
78.5 ~ 88.3
8.0 ~ 9.0
57.9 ~ 65.1
Trailing arm mounting bolt
44.1 ~ 53.9
4.5 ~ 5.5
32.5 ~ 39.7

Lubricants
 Engine & T/M
Joint type
Lubricants
Quantity
Lambda 3.3 GDI
BJ#26
RBA
160g
VTJ#25
CW-13TJ
170g

    Special Service Tools Tool Name / NumberIllustrationDescriptionBand installer09495-3K000Installation of ear type boot bandBand installer09495-39100Installation of hook type boot bandLower arm ball joint remover0K545-A9100Removal of front lower arm from front axle

    Other information:

    Kia Cadenza YG 2016-2021 Service Manual: Surround View Monitoring Unit Repair procedures

    Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the glove box housing. (Refer to Body - "Glove Box Housing") 3. Remove the SVM unit (B) after disconnecting the connectors (A) and mounting bolts. Installation 1. Install the SVM unit.

    Kia Cadenza YG 2016-2021 Service Manual: Start/Stop Button Repair procedures

    Removal 1. Disconnect the negative (-) battery terminal. 2. Using a screw driver or remover, remove the center fascia lower panel (A). 3. Remove the in-car hose (A) and disconnect the connectors (B) from the heater & A/C control unit. 4.

    Categories

     
    Copyright © 2026 www.kcadenzavg.com - 0.0224