Kia Cadenza YG: Front Suspension System / Front Lower Arm Repair procedures

Kia Cadenza YG 2016-2021 Service Manual / Suspension System / Front Suspension System / Front Lower Arm Repair procedures

Replacement
1.
Remove the front wheel & tire.
Tightening torque:
88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)
   
Be careful not to damage to the hub bolts when removing the front wheel & tire.
2.
Loosen the bolt & nut and then remove the lower arm (A).
Tightening torque:
98.1~117.7N.m (10.0~12.0kgf.m, 72.3 ~ 86.6lb-ft)

3.
Remove the front lower arm from the front knuckle using the SST (0K545-A9100).
(1)
After removing bolts from the front knuckle, install and tighten the sub body bolt (A) .

(2)
Input the sub body (A) between the front knuckle and the sub body bolt.
(3)
Tighten bolt (B) of the sub body bolt to broaden the gap of the front knuckle.

(4)
Install the safe wire (A).

   
Install a safe wire on the front strut to prevent dropping the SST and hurting technicians.
(5)
Install the main body, between the front strut and the lower arm.

(6)
To avoid the main body coming off, install a fixing clamp (A) beside the main body.

(7)
After installing a fixing clamp, rotate the handle (B) clock wise till the clamp is fixed on a lower arm.

(8)
Tighten a main body bolt (A) of the slowly and remove the lower arm from the front knuckle.

4.
Remove the front lower arm (A) and than loosen the bolts & nuts.
Tightening torque
Front:
117.7 ~ 137.3N.m (12.0 ~ 14.0kgf.m, 86.8 ~ 101.3lb-ft)
Rear:
156.9 ~ 176.5N.m (16.0 ~ 18.0kgf.m, 115.7 ~ 130.2lb-ft)

5.
Installation is the reverse of removal.
Inspection
1.
Check the bushing for wear and deterioration.
2.
Check the front stabilizer bar for deformation.
3.
Check the all bolts and nuts.

    Replacement 1. Remove the front wheel & tire. Tightening torque: 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)     Be careful not to damage to the hub bolts when removing the front wheel & tire.

    Replacement 1. Remove the front wheel & tire. Tightening torque: 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)     Be careful not to damage to the hub bolts when removing the front wheel & tire.

    Other information:

    Kia Cadenza YG 2016-2021 Service Manual: Pantoscopic Camera Repair procedures

    Removal Front Pantoscopic Camera 1. Disconnect the negative (-) battery terminal. 2. Remove the front bumper cover. (Refer to Body - "Front Bumper Cover") 3. Remove the pantocscpic camera (B) after loosening the mounting screws and connector (A).

    Kia Cadenza YG 2016-2021 Service Manual: Receiver-Drier Repair procedures

    Replacement 1. Remove the condenser, and then remove the bottom cap (B) with L wrench (A) from the condenser. Tightening torque : 9.8~14.7N.m (1.0~1.5kgf.m, 7.2~10.8 lb-ft) 2. Remove the desiccant (A) from condenser using a long nose plier.

    Categories

     
    Copyright © 2026 www.kcadenzavg.com - 0.0219