Kia Cadenza YG: Tires/Wheels / Alignment Repair procedures

Kia Cadenza YG 2016-2021 Service Manual / Suspension System / Tires/Wheels / Alignment Repair procedures

Front wheel alignment
   
When using a commercially available computerized wheel alignment equipment to inspect the front wheel alignment, always position the vehicle on a level surface with the front wheels facing straight ahead.
Prior to inspection, make sure that the front suspension and steering system are in normal operating condition and that the tires are inflated to the specified pressure.
Toe

B - A > 0: Toe in (+)
B - A ＜ 0: Toe out (-)
Toe adjustment
1.
Loosen the tie rod end lock nut.
2.
Remove the bellows clip to prevent the bellows from being twisted.
3.
Adjust the toe by screwing or unscrewing the tie rod. Toe adjustment should be made by turning the right and left tie rods by the same amount.
Toe
Total : 0° ± 0.2°
Individual : 0° ± 0.1°

4.
When completing the toe adjustment, install the bellows clip and tighten the tie rod end lock nut to specified torque.
Tightening torque:
49.0 ~ 53.9N.m (5.0 ~ 5.5kgf.m, 36.2 ~ 39.8lb-ft)
Camber and Caster
Camber and Caster are pre-set at the factory, so they do not need to be adjusted. If the camber and caster are not within the standard value, replace or repair the damaged parts and then inspect again.
Camber angle:
LH (-0.5°±0.5°), RH (-0.8°±0.5°)
Caster angle : 4.38° ± 0.5°
Rear wheel alignment
   
When using a commercially available computerized wheel alignment equipment to inspect the rear wheel alignment, always position the vehicle on a level surface.
Prior to inspection, make sure that the rear suspension system is in normal operating condition and that the tires are inflated to the specified pressure.
Toe

B - A > 0: Toe in (+)
B - A ＜ 0: Toe out (-)
Toe adjustment
1.
Loosen the nut holding the assist arm cam bolt (A).
2.
Adjust rear toe by turning the rear assist arm cam bolt (A) clockwise or counter clockwise. Toe adjustment should be made by turning the right and left cam bolt by the same amount.
Toe
Total : 0.17° ± 0.2°
Individual : 0.085° ± 0.1°

3.
When completing the toe adjustment, tighten the nut to specified torque.
Tightening torque:
137.3 ~ 156.9N.m (14.0 ~ 16.0kgf.m,101.3 ~ 115.7lb-ft)
Camber
Camber is pre-set at the factory, so it does not need to be adjusted. If the camber is not within the standard value, replace or repair the damaged parts and then inspect again.
Camber: -1.0° ± 0.5°

    Hub nut tightening sequence Tighten the hub nuts as follows. Tightening torque: 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)     When using an impact gun, final tightening torque should be checked using a torque wrench.

    Other information:

    Kia Cadenza YG 2016-2021 Service Manual: Auto Head lamp leveling Unit Repair procedures

    Removal Height Sensor 1. Remove the height sensor connector (A). 2. Loosen the mounting bolts(Body: 2EA, chassis: 1EA) from height sensor bracket. Tightening torque : 3 ~ 5N.m (30 ~ 50kgf.m, 2.21 ~ 3.68lb-ft) 3. Remove the height sensor.

    Kia Cadenza YG 2016-2021 Service Manual: Climate Control Air Filtar Repair procedures

    Replacement 1. Disconnect the damper (B) from the glove box (A) and then remove the glove box lift (C). 2. Remove the filter cover (A) with pushing the knob. 3. Replace the air filter (B), install it after making sure of the direction of air filter.

    Categories

     
    Copyright © 2025 www.kcadenzavg.com - 0.024