Kia Cadenza YG: Interior / Interior Trim Repair procedures
Door Scuff Trim Replacement
|
•
|
Put on gloves to protect your hands. |
|
•
|
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage. |
|
•
|
Take care not to bend or scratch the trim and panels. |
|
| 1. |
Using a screwdriver or remover, remove the front door scuff tirm (A).
[Front] 
|
| 2. |
Disconnect the connector (A). 
|
| 3. |
Remove the rear seat.
(Refer to the BD group - "Rear Seat") |
| 4. |
After loosening the mounting screws, then remove rear door scuff trim (A).
[Rear] 
|
| 5. |
Installation is the reverse of removal.
|
•
|
Replace any damage clips. |
|
|
Front Pillar Trim Replacement
|
•
|
Put on gloves to protect your hands. |
|
•
|
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage. |
|
•
|
Take care not to bend or scratch the trim and panels. |
|
| 1. |
After loosening the mounting bolt, then remove the front pillar trim (A). 
|
| 2. |
Installation is the reverse of removal.
|
•
|
Replace any damage clips. |
|
|
Cowl Side Trim Replacement
|
•
|
Put on gloves to protect your hands. |
|
•
|
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage. |
|
•
|
Take care not to bend or scratch the trim and panels. |
|
| 1. |
Remove the front door scuff trim. |
| 2. |
Remove the hood latch release handle.
(Refer to the BD group - "Hood") |
| 3. |
After loosening the mounting screw, then remove the cowl side trim (A). 
|
| 4. |
Installation is the reverse of removal. |
Center Pillar Trim Replacement
|
•
|
Put on gloves to protect your hands. |
|
•
|
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage. |
|
•
|
Take care not to bend or scratch the trim and panels. |
|
| 1. |
Remove the front door scuff trim and rear door scuff trim. |
| 2. |
The seat belt anchor pretensioner (A) be removed after pushing the lock pin (B) as arrow direction. 
|
| 3. |
Remove the center pillar lower trim (A). 
|
| 4. |
After loosening the mounting bolts, then remove the center pillar upper trim (A). 
|
| 5. |
Installation is the reverse of removal.
|
•
|
Replace any damaged clips. |
|
|
Rear Pillar Trim Replacement
|
•
|
Put on gloves to protect your hands. |
|
•
|
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage. |
|
•
|
Take care not to bend or scratch the trim and panels. |
|
| 1. |
After loosening the mounting bolt, then remove the rear pillar trim (A). 
|
| 2. |
Installation is the reverse of removal.
|
•
|
Replace any damaged clips. |
|
|
Package Tray Trim Replacement
|
•
|
Put on gloves to protect your hands. |
|
•
|
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage. |
|
•
|
Take care not to bend or scratch the trim and panels. |
|
| 1. |
Remove the rear seat assembly.
(Refer to the BD group - "Rear Seat") |
| 2. |
Remove the trunk trim.
(Refer to the BD group - "Trunk Trim") |
| 3. |
After loosening the mounting bolt, then remove the rear seat belt lower anchor (A).
Tightening torque:
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
| 4. |
After loosening the mounting bolt, then remove the rear center seat belt lower anchor (A).
Tightening torque:
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
| 5. |
After loosening the mounting bolt, then remove the rear pillar trim (A).
|
| 6. |
Loosen the trunk inner mounting nuts. 
|
| 7. |
After loosening the mounting screws, then remove the package tray trim (A). 
|
| 8. |
Disconnect the connector (A). 
|
| 9. |
Installation is the reverse of removal.
|
•
|
Replace any damage clips. |
|
•
|
Make sure the connector is connected properly. |
|
|
Components
1. Front pillar trim2. Center pillar upper trim3. Center pillar lower trim4. Rear pillar trim5. Cowl side trim6. Front door scuff trim7.
Replacement
•
Put on gloves to protect your hands.
•
When plying with a flat-tip screwd river, wrap it with protective tape to prevent damage.
