Kia Cadenza YG: Interior / Roof Trim Repair procedures

Replacement
Sunvisor Replacement
   
•
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
•
Put on gloves to protect your hands.
1.
Loosen the mounting screws, then remove the sunvisor (A) and retainer (B).

2.
Installation is the reverse of removal.
Assist Handle Replacement
   
•
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
•
Put on gloves to protect your hands.
1.
Remove the covers (A) and screws, then remove the assist handle (B).

2.
Installation is the reverse of removal.
Deluxe Overhead Lamp Replacement
   
•
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
•
Put on gloves to protect your hands.
1.
After loosening the mounting bolts, remove the deluxe overhead lamp(A).

2.
Disconnect the connector (A).

3.
Installation is the reverse of removal.
   
•
Make sure the connector is plugged in properly.
•
Replace any damage clips.
Vanity Lamp Replacement
1.
Using a screwdriver or remover, remove the vanity lamp (A).
2.
Disconnect the vanity lamp connector (B).

3.
Installation is the reverse of removal.
   
•
Make sure the connector is plugged in properly.
Roof Trim Replacement
   
•
Put on gloves to protect your hands.
•
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the following items:
•
Front seat
(Refer to the BD group - "Front Seat")
•
Rear seat
(Refer to the BD group - "Rear Seat")
•
Sunvisor
•
Deluxe overhead lamp
•
Room lamp
•
Assist handle
•
Front pillar trim
(Refer to the BD group - "Interior Trim")
•
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - "Interior Trim")
•
Canter pillar lower trim
(Refer to the BD group - "Interior Trim")
•
Canter pillar upper trim
(Refer to the BD group - "Interior Trim")
•
Rear pillar trim
(Refer to the BD group - "Interior Trim")
2.
Remove the ECM mirror cover (A).
3.
Disconnect the ECM mirror connector (B).

4.
Remove the auto defog sensor & rain sensor cover (A).

5.
Disconnect the auto defog sensor connector (A) and rain sensor connector (B).

6.
Remove the LDWS cover (A).

7.
Disconnect the LDWS connector (A).

8.
Disconnect the roof trim main connectors (A).
[Driver''s]

[Passenger''s]

9.
Disconnect the antenna connector (A).
[LH]

[RH]

10.
Remove the clips and roof trim (A).

11.
Installation is the reverse of removal.
   
•
Replace any damage clips.
•
Make sure the connector is plugged in properly.

    Components 1. Roof trim2. Sunvisor3. Retainer4. Assist handle bracket Components (Panoramaroof) 1. Roof trim2. Sunvisor3. Retainer4. Assist handle bracket

    Components 1. Front pillar trim2. Center pillar upper trim3. Center pillar lower trim4. Rear pillar trim5. Cowl side trim6. Front door scuff trim7.

    Other information:

    Kia Cadenza YG 2016-2021 Service Manual: Description and Operation

    Description The immobilizer system will disable the vehicle unless the proper ignition key is used, in addition to the currently available anti-theft systems such as car alarms, the immobilizer system aims to drastically reduce the rate of auto theft.

    Kia Cadenza YG 2016-2021 Service Manual: Description and Operation

    Description Back view camera will activate when the backup light is ON with the ignition switch ON and the shift lever in the R position. This system is a supplemental system that shows behind the vehicle through the ECM (Reverse Display Room Mirror) mirror or AVN head unit while backing-up.

    Categories

     
    Copyright © 2026 www.kcadenzavg.com - 0.0259