Kia Cadenza YG: Exterior / Trunk Lid Repair procedures

Kia Cadenza YG 2016-2021 Service Manual / Body (Interior and Exterior) / Exterior / Trunk Lid Repair procedures

Replacement
Trunk Lid Assembley Replacement
   
•
When removing and installing the trunk lid, an assistant is necessary.
•
Wear gloves to protect hands from injury.
1.
After loosening the mounting screws, then remove the trunk inside handle (A).

2.
Detach the clips, then remove the trunk lid trim (A).

3.
Disconnect wiring (B) and connectors.
4.
After loosening the mounting bolts, then remove the trunk lid (A).
Tightening torque:
6.9~8.8 N.m (0.7~0.9 kgf.m, 5.1~6.5 lb-ft)

5.
Installation is the reverse of removal.
   
•
Replace any damaged clips.
Trunk Lid Weatherstrip Replacement
1.
Remove the trunk lid weatherstrip (A).
   
•
Do not apply sealant to the body.

2.
Installation is the reverse of removal.
   
•
Install the weatherstrip aligned with canter line (B).
Key Holder Replacement
1.
Remove the trunk lid trim.
2.
Disconnect the inside handle cable (A), then loosen the key holder (B) mounting clips and remove.

3.
Installation is the reverse of removal.
Trunk Lid Latch Replacement
1.
Remove the trunk lid trim.
2.
Disconnect the trunk lid latch connector (A).
3.
Disconnect the cable (B), then loosen the latch assembly (C) mounting bolts and remove.
Tightening torque:
6.9~10.8 N.m (0.7~1.1 kgf.m, 5.1~8.0 lb-ft)

4.
Installation is the reverse of removal.
   
•
Make sure the trunk lid locks/unlocks and opens/closes properly.
Trunk Lid Back Panel Replacement
   
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Put on gloves to protect your hands.
1.
Remove the trunk lid trim.
2.
After loosening the mounting nuts, then disconnect the rear combination lamp connector (B).
3.
Remove the rear combination lamp (A).

4.
Loosen the trunk lid back panel mounting nuts (A).

5.
Using a screwdriver or remover, remove the trunk lid back panel (A).

6.
Installation is the reverse of removal.
   
•
Replace any damaged clips.
Adjustment
1.
After loosening the trunk lid hinge (A) mounting bolt, adjust the trunk lid by moving it up or down, or right or left.
2.
Adjust the trunk lid height by turning the trunk lid overslam bumpers (B).
3.
After loosening the trunk lid striker (C) mounting bolts, adjust the trunk lid striker by moving it up or down, or right or left.

    Replacement Hood Assembly Replacement     • When removing and installing the hood, an assistant is necessary. • Be careful not to damage the hood and body.

    Components 1. Front door trim2. Front door inside cap3. Front door frame inner cover4. Front door belt inner weatherstrip5. Front door panel6. Front door upper opening weatherstrip7.

    Other information:

    Kia Cadenza YG 2016-2021 Service Manual: Refrigerant line Repair procedures

    Replacement 1. Discharge refrigerant from refrigeration system. 2. Replace faulty tube or hose.     Cap the open fittings immediately to keep moisture or dirt out of the system. 3. Tighten joint of bolt or nut to specified torque.

    Kia Cadenza YG 2016-2021 Service Manual: A/C Pressure Transducer Description and Operation

    Description A/C pressure transducer convert the pressure value of high pressure line into voltage value after measure it. By converted voltage value, engine ECU controls cooling fan by operating it high speed or low speed. Engine ECU stop the operation of compressor when the temperature of refrigerant line is so high or so low irregularl

    Categories

     
    Copyright © 2026 www.kcadenzavg.com - 0.0312